电压对电刷镀三价铬镀层性能的影响

在45钢表面电刷镀得到三价铬镀层,镀液组成和工艺条件为:Cr2(SO4)36H2O 0.4 mol/L,甲酸铵0.5 mol/L,氨基乙酸0.5 mol/L,H3BO30.6 mol/L,NaH2PO2 H2O 0.3 mol/L,pH=1.5,温度50°C,镀笔移动速率15 cm/s。研究了电压对镀铬层显微结构、表面粗糙度、厚度、显微硬度和耐磨性的影响。随电压增大,镀层厚度增大,显微硬度和耐磨性均先提高后降低。电压为14 V时,镀层的表面平整,粗糙度为2.387μm,显微硬度为602 HV,耐磨性最好。     

A highly active composite electrocatalyst Ni–Fe–P–Nb2O5/NF for overall water splitting

This work demonstrates a facile Nb₂O₅-decorated electrocatalyst to prepare cost-effective Ni–Fe–P–Nb₂O₅/NF and compared HER & OER performance in alkaline media. The prepared electrocatalyst presented an outstanding electrocatalytic performance towards hydrogen evolution reaction, which required a quite low overpotential of 39.05 mV at the current density of ?10 mA cm^?2 in 1 M KOH electrolyte. Moreover, the Ni–Fe–P–Nb₂O₅/NF catalyst also has excellent oxygen evolution efficiency, which needs only 322 mV to reach the current density of 50 mA cm^?2. Furthermore, its electrocatalytic performance towards overall water splitting worked as both cathode and anode achieved a quite low potential of 1.56 V (10 mA cm^?2).     

硼氢化钠对滑轮用铸钢板化学镀Ni-B合金薄膜性能的影响

在滑轮用铸钢板上化学镀Ni-B合金薄膜,并研究了硼氢化钠的质量浓度对化学镀Ni-B合金薄膜性能的影响。结果表明:适当增加硼氢化钠的质量浓度,有利于增大化学镀Ni-B合金薄膜的厚度及硼的质量分数,从而提高化学镀Ni-B合金薄膜的硬度。当硼氢化钠的质量浓度大于1.2 g/L时,硼氢化钠的水解速率加快及剧烈的析氢反应,导致化学镀Ni-B合金薄膜的厚度及硬度有所降低。当硼氢化钠的质量浓度为1.2 g/L时,化学镀Ni-B合金薄膜表面"胞状"颗粒均匀、致密,摩擦因数和磨损率最低,具有最佳的耐磨性。     

Simplification of the Plasma Load of Negative-Pulse-Bias Source Used in Arc Ion Plating

Based on the voltage and current fluctuating phenomenon in the arc plasma load under the negative-pulse-bias, usingthe plasma physics theory and analysis of computer simulation expatiates that the nature of plasma load in vacuumarc plasma is a capacitance     

陶瓷表面化学镀的前处理工艺新进展

综述了非金属表面化学镀前处理工艺的现状和发展，对陶瓷化学镀的粗化和活化工艺的新进展进行了评述，侧重讨论了离子型、胶体钯型、浆料型、分子自组装吸附钯型、贱金属型活化工艺特点和进展，并展望了今后发展方向。     

化学复合镀层激光处理研究

研究了激光处理对Ni-P -SiC化学复合镀层的影响。借助于扫描电镜、能谱仪、X射线衍射、显微硬度计等设备对激光处理后复合镀层的表面形貌、组织结构及性能进行了综合分析。结果表明 ,对复合镀层进行激光处理可以获得与炉内加热同样的镀层硬度 ,且当激光功率 4 0 0W ,扫描速度 1.5m /min时 ,镀层硬度高于炉内加热的硬度     

玻璃微珠的表面化学镀银及红外辐射性能研究

采用化学镀方法在玻璃微珠表面镀银,考察了预处理条件、反应温度和反应时间等因素对玻璃微珠表面镀银的影响,并通过扫描电镜和X-射线衍射分析仪,对镀银后玻璃微珠的表面形貌和结构进行了观察和表征。将镀银玻璃微珠用于涂料中,考察了玻璃微珠在涂料中的应用及其红外辐射率的变化,探讨了化学镀条件对涂料红外辐射率的影响,结果表明,在控制反应温度和浓度的条件下,可使镀银玻璃微珠的红外辐射率由原来的1.02降为0.70,将其应用于涂料后,涂层的红外辐射率为0.80。     

镍层耐硝酸腐蚀性测试——一种简单的预先探测ENIG镍层“黑盘”现象的测试方法

随着更加精细的SMT、BGA等表面贴装技术的运用,化学沉镍金(ENIG)作为线路板最终表面处理得到了越来越广泛的应用,同时可怕的“黑盘”现象也随之更广泛地“流行”起来,直接导致贴装后元器件焊接点不规则接触不良。为了贯彻执行最好的流程控制和采取有效的预防措施,了解这种焊接失败的产生机理是非常重要的,及早的观测到可能发生“黑盘”现象的迹象变得同样关键。本文介绍了一种简单的预先探测ENIG镍层“黑盘”现象的测试方法-镍层耐硝酸腐蚀性测试,这种测试可以用于作为一种常规的测试方法监测一般化学沉镍溶液在有效使用寿命范围内新鲜沉积的镍层的质量。利用Weibull概率统计分析在不同的金属置换周期(MTO)下镍层的可靠性能表现。结合试验结果得出了一个镍层耐硝酸腐蚀性的判定标准。     

Effect of Rare Earth Element Cerium on Mechanical Properties and Morphology of TiN Coating Prepared by Arc Ion Plating

TiN coatings were deposited on polished substrates of W18Cr4V high speed steel by means of vacuum arc ion plating. The effect of cerium on adhesion between TiN coating and substrate was studied. The microstructures and composition of TiN coatings were also investigated by means of scanning electron microscope (SEM), Auger electron spectroscopy (AES), and X-ray diffraction (XRD) technique. It was found that cerium is an effective modifying agent and the addition of suitable amount of cerium to TiN coatings can produce relatively excellent properties such as micro-hardness, wear resistance, oxidation resistance and porosity. The experimental results show that the added cerium in TiN coatings makesa contribution to form the preferred direction along with a (111 ) or (222) close packed face, which may be one of the reasons that improves some properties mentioned above.     

化学镀Ni-P合金/TiO2复合膜的耐蚀性研究

在改进常规制备方法的基础上，提出化学镀/溶胶-凝胶复合法在碳钢表面制备TiO2复合膜的新技术。用衍射研究了复合膜的组织形态，采用环境扫描电镜（ESEM）表征了复合膜的表观和断面形貌，用极化电阻、阳极极化曲线测量等方法研究TiO2复合膜在0.5mol/L硫酸和0.5mol/L氯化钠溶液中的耐蚀性能。结果表明A3钢表面的TiO2复合膜耐蚀性能优良。